The article following next in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is especially entertaining. You should read it.
Setting up a tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is additionally a reasonably difficult project. If the old bathtub is easily available, the project can relocate easily; if you need to open a wall surface to remove the old tub as well as position the brand-new tub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and embeded in the new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is far better to think about using one before you start. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly assist you set up a brand-new bathtub in your restroom if you have actually already bought a brand-new tub and also don't require to change the plan of your previous water pipes.
Your tools and material list must consist of the following:
Planning for the Setup
First of all, the sustaining frame supplied with the bath ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipelines have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The next objective is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the other faucet.
Switch on the water supply and check all joints and new pipework for leakages as well as tighten them if essential. Load the tub and additionally check the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the tub ought to wait until the bath tub has been made use of at the very least once as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers are in location in between the tap and the sink. Secure the faucet in position with the maker given backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, resulting in complications with wetness and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as installations. They are sold in tubes and cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can break rather early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the market. It is suggested to fit the tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about How to Install a Bathtub Yourself, I imagined sharing that piece of content was a smart idea. Loved our article? Please share it. Help others check it out. Many thanks for your time spent reading it.
Quality care? Call.